Test date | Expiry date | Result | Odometer reading |
2023-06-06 | 2024-06-05 | ✓ Pass | 141,675 |
- Driver's view to the front outside the swept area of the windscreen wipers restricted by an obstruction (3.1 (a) (i))
- Front brake disc worn, but not excessively (1.1.14 (a) (i))
- Front brake pad(s) wearing thin (1.1.13 (a) (ii))
- Front service brake imbalance requirements only just met. it would appear that the braking system requires adjustment or repair. (1.2.1 (b) (i))
- Nearside front brake pipe corroded, covered in grease or other material (1.1.11 (c))
- Nearside front inner integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))
- Nearside rear anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
- Nearside rear brake cable damaged but not to excess (1.1.15 (a))
- Nearside rear leaf spring slighty splayed
- Nearside rear vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))
- Offside front inner integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))
- Offside rear anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
- Offside rear brake cable damaged but not to excess (1.1.15 (a))
- Offside rear brake pipe clips or supports missing, pipe adequately supported (1.1.11 (d) (i))
- Oil leak, but not excessive (8.4.1 (a) (i))
- Power steering component has slight seepage from a component (2.1.5 (a))
- Rear service brake imbalance requirements only just met. it would appear that the braking system requires adjustment or repair. (1.2.1 (b) (i))
- Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))
|
2023-05-19 | - | ✗ Fail | 141,655 |
- Clutch pedal pivot worn
- Driver's view to the front outside the swept area of the windscreen wipers restricted by an obstruction sunvisor (3.1 (a) (i))
- Front brake pad(s) wearing thin (1.1.13 (a) (ii))
- Nearside front brake pipe corroded, covered in grease or other material (1.1.11 (c))
- Nearside front integral body structure is corroded but structural rigidity is not significantly reduced inner arch (6.1.1 (c) (i))
- Nearside rear leaf spring slightly splayed
- Nearside rear anti-roll bar pin or bush worn but not resulting in excessive movement d bush (5.3.4 (a) (i))
- Nearside rear outer tyre has a cut but not deep enough to reach the ply or cords (5.2.3 (d) (i))
- Nearside registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))
- Offside front integral body structure is corroded but structural rigidity is not significantly reduced inner arch (6.1.1 (c) (i))
- Offside front suspension component mounting prescribed area is corroded but not considered excessive top of chassis (5.3.6 (a) (i))
- Offside rear anti-roll bar pin or bush worn but not resulting in excessive movement d bush (5.3.4 (a) (i))
- Offside rear brake pipe clips or supports missing, pipe adequately supported (1.1.11 (d) (i))
- Offside rear brake pipe corroded, covered in grease or other material (1.1.11 (c))
- Offside rear service brake binding but not excessively (1.2.1 (f))
- Offside rear vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))
- Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))
- All direction indicators not working when brake pedal depressed (4.4.1 (a) (ii))
- Brake fluid significantly below minimum mark (1.1.10 (d) (ii))
- Brake pedal anti-slip provision missing (1.1.2 (c))
- Brake pedal has insufficient reserve travel (1.1.2 (a))
- Brake performance unable to be tested due to brake fluid leak (1.2.1 (g))
- Driver's door cannot be opened from outside the vehicle (6.2.3 (a))
- Fuel cap/sealing device missing (6.1.3 (b) (i))
- Horn not working (7.7 (a))
- Nearside front lower suspension arm ball joint excessively worn (5.3.4 (a) (i))
- Nearside rear hydraulic brake cylinder leaking hydraulic fluid (1.1.16 (b) (i))
- Nearside rear inner tyre tread depth below requirements of 1.6mm (5.2.3 (e))
- Nearside rear position lamp not working (4.2.1 (a) (ii))
- Nearside seat belt anchorage prescribed area strength or continuity significantly reduced rear end. inner sill, outer sill, door shut (7.1.1 (a) (i))
- Offside front suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis, bottom and side, visable in wheel arch (5.3.6 (a) (i))
- Offside rear inner tyre tread depth below requirements of 1.6mm (5.2.3 (e))
- Offside rear position lamp adversely affected by the operation of another lamp (4.2.3 (c))
- Offside rear rear fog lamp adversely affected by the operation of another lamp (4.5.4 (b))
- Offside seat belt anchorage prescribed area strength or continuity significantly reduced central area. outer sill (7.1.1 (a) (i))
- Offside seat belt anchorage prescribed area strength or continuity significantly reduced rear end. inner sill, door shut (7.1.1 (a) (i))
- Offside side repeater not working (4.4.1 (a) (ii))
- Oil leaking excessively from engine (8.4.1 (a) (i))
|
2022-04-02 | 2023-04-01 | ✓ Pass | 136,630 |
- Brake pedal wearing smooth (1.1.2 (c))
- Nearside front suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))
- Nearside front suspension arm ball joint has slight play (5.3.4 (a) (i))
- Offside rear anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
- Oil leak, but not excessive (8.4.1 (a) (i))
- Rear integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))
|
2021-03-19 | 2022-03-18 | ✓ Pass | 128,832 |
- Brake pedal wearing smooth (1.1.2 (c))
- Rear outer integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))
|
2021-03-19 | - | ✗ Fail | 128,832 |
- Brake pedal wearing smooth (1.1.2 (c))
- Rear outer integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))
- Headlamp aim too high both (4.1.2 (a))
|
2021-03-15 | - | ✗ Fail | 128,698 |
- Brake pipe inadequately clipped or supported front to rear (1.1.11 (d) (i))
- Nearside front brake pipe corroded, covered in grease or other material (1.1.11 (c))
- Nearside rear anti-roll bar pin or bush worn but not resulting in excessive movement d bush (5.3.4 (a) (i))
- Nearside rear lower anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
- Nearside rear wheel bearing has slight play (5.1.3 (a) (i))
- Offside front brake pipe corroded, covered in grease or other material (1.1.11 (c))
- Offside rear anti-roll bar pin or bush worn but not resulting in excessive movement d bush (5.3.4 (a) (i))
- Offside rear brake pipe inadequately clipped or supported (1.1.11 (d) (i))
- Offside rear lower anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
- Offside rear registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))
- Offside rear wheel bearing has slight play (5.1.3 (a) (i))
- Oil leak, but not excessive (8.4.1 (a) (i))
- Rear passenger seat(s) missing at time of test all ()
- Brake pedal anti-slip provision missing (1.1.2 (c))
- Exhaust emissions exceed manufacturer's specified limit (8.2.2.2 (a))
- Front tyre(s) of different sizes are fitted on the same axle. (5.2.3 (b))
- Horn not working (7.7 (a) (ii))
- Nearside front headlamp aim too low (4.1.2 (a))
- Nearside front headlamp levelling device cannot be operated from the driver's seat (4.1.5 (b))
- Nearside front integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch (6.1.1 (c) (i))
- Nearside front suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))
- Nearside front upper position lamp not working (4.2.1 (a) (ii))
- Nearside fuel cap/sealing device missing (6.1.3 (b) (i))
- Nearside rear integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i))
- Nearside rear tyre(s) with different aspect ratios are fitted on twin wheels (5.2.3 (b))
- Offside front bumper insecure (6.1.4 (a) (i))
- Offside front headlamp aim too low (4.1.2 (a))
- Offside front integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i))
- Offside front integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))
- Offside front tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i))
- Offside front upper position lamp not working (4.2.1 (a) (ii))
|
2020-02-22 | 2021-02-21 | ✓ Pass | 111,823 |
- Nearside front lower suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))
- Nearside rear corrosion to step / out of prescribed areas
- Offside rear corrosion to outer sill / out of prescribed areas
- Offside rear outer tyre perishing
- Passenger seat(s) missing at time of test all rear ()
|
2019-02-19 | 2020-02-18 | ✓ Pass | 106,658 |
2018-01-23 | 2019-01-22 | ✓ Pass | 99,327 |
2018-01-17 | - | ✗ Fail | 99,316 |
- Nearside front inner suspension arm rubber mounting deteriorated resulting in excessive movement (2.4.g.2)
- Nearside rear inner tyre tread depth below requirements of 1.6mm (4.1.e.1)
|
2016-11-16 | 2017-11-15 | ✓ Pass | 95,542 |
2015-09-19 | 2016-09-18 | ✓ Pass | 91,908 |
2014-09-11 | 2015-09-16 | ✓ Pass | 87,293 |
- Both rear n/s tyres are perishing
- Both rear n/s tyres have multiple nails in the tread
- The front bumper is damaged
- The n/s front brake pads are wearing thin
- The n/s outer sill is holed to the rear but not within a prescribed area
- The n/s rear outer tyre has side wall damage
- The rear body door is in poor condition
- The rear exhaust box outer skin is in poor condition
- The windscreen is slightly damaged
|
2013-09-17 | 2014-09-16 | ✓ Pass | 79,589 |
- Both front brake pipes coated in oil (unable to inspect )
|
2013-09-12 | - | ✗ Fail | 79,561 |
- Both front brake pipes coated in oil (unable to inspect )
- Nearside front lower suspension arm rubber bush bonding deteriorated resulting in excessive movement (2.4.g.2)
- Offside rear position lamp(s) not working (1.1.a.3b)
|
2012-09-12 | 2013-09-13 | ✓ Pass | 75,472 |
- Body slightly corroded
- Centre brake pipe slightly corroded (3.6.b.2c)
- Offside front front wheel bearing has slight play (2.5.a.3c)
- Power steering component(s) has slight seepage from a component (2.3.3b)
|
2011-09-14 | 2012-09-13 | ✓ Pass | 70,032 |
- Nearside front brake pipe slightly corroded (3.6.b.2c)
- Offside front brake pipe slightly corroded (3.6.b.2c)
|
2010-09-13 | 2011-09-12 | ✓ Pass | 68,506 |
2010-09-08 | - | ✗ Fail | 68,506 |
- Nearside rear anti-roll bar has excessive play in a pin/bush (2.4.g.2)
- Nearside stop lamp not working (1.2.1b)
- Offside rear anti-roll bar has excessive play in a pin/bush (2.4.g.2)
- Windscreen has damage to the swept area in excess of a 40mm circle outside zone 'a' (8.3.1d)
|
2009-09-11 | 2010-09-10 | ✓ Pass | 65,961 |
- Deep cuts in near side front tyre
- Front pads low and discs in poor condision
- Near side rear seat not fitted,but belts there and not sacure
- Nearside front suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.g.2)
|
2009-09-11 | - | ✗ Fail | 65,959 |
- Deep cuts in near side front tyre
- Front pads low and discs in poor condision
- Near side rear seat not fitted,but belts there and not sacure
- Nearside front suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.g.2)
- Offside inner rear tyre worn close to the legal limit (4.1.e.1)
- Nearside inner rear tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.d.1a)
- Nearside outer rear tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.d.1a)
- Offside front suspension arm rubber bush deteriorated resulting in excessive movement (2.4.g.2)
- Offside front tyre has a cut in excess of the requirements deep enough to reach the ply or cords (4.1.d.1a)
- Offside windscreen wiper does not clear the windscreen effectively (8.2.2)
|
2008-06-23 | 2009-06-22 | ✓ Pass | 60,804 |
2008-06-20 | - | ✗ Fail | 60,804 |
- Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
- Front brake lining(s) wearing thin (3.5.1g)
- Offside rear fog lamp not working (1.3.2b)
- Windscreen has damage to an area in excess of a 10mm circle within zone 'a' (8.3.1a)
- Windscreen washer provides insufficient washer liquid (8.2.3)
|
2007-06-21 | 2008-06-22 | ✓ Pass | 57,412 |
2006-06-23 | 2007-06-22 | ✓ Pass | 53,285 |